MATERIAL SAFETY DATA SHEET

Trade Name: BRIGHT GREEN COLOUR PIGMENT
Chemical Family: Unsaturated Polyester Resin
Formula: N/A

Manufacturer: PERFORMANCE COLORS
#1-8307 - 124 Street
Surrey, BC V3W 9G2
Emergency Ph. #'s: (604) 590-0804
Transportation EMG. Phone # CANUTEC (613) 996-6 or (250) 727-3545

Supplier: Industrial Plastics (1975) Ltd
3944 Quadra St.,
Victoria, BC V8X 1J6
(250) 727.3545

HAZARDOUS INGREDIENTS:
Ferric Oxide: 0.3 % CAS# 1309-37-1
Silica, Amphorus: 1.0 % CAS# 7631-86-9
Lead Chromate: 0.6 % CAS# 7758-97-6
Lead Sulfate: 0.4 % CAS# 7446-14-2
Chromium Oxide: 40.0 % CAS# 1308-38-9

Exposure Limits:

Lead Chromate: ACGIH TLV 0.5mg/m3 Cr
Lead Sulfate: ACGIH TLV 0.15 mg/m3 Pb
Chromium Oxide: ACGIH TLV 0.5 / 1.0 mg/m3

PHYSICAL DATA:
Appearance & Odour: Green paste, pungent odour.
Vapour Pressure:.008 mmHg at 20C
Vapour Density: (Air = 1) >1
Solubility in Water: Nil
Specific Gravity: >1
Evaporation Rate: Slower than n-Butyl Acetate
Boiling Point: N/A
Freezing Point: N/A
pH: N/A

FIRE & EXPLOSION DATA:
Flashpoint & Method: 98.9C Seta flash, CC, Resin
Flammable Limits: N/A
Extinguishing Methods: Foam, Carbon Dioxide, Dry chemical, Water fog
Special Equipment & Procedures: Self contained breathing apparatus.

REACTIVITY DATA:
Conditions Contributing to Instability: Heat and direct sunlight
Incompatible Substances : Oxidizing agents & strong acids
Hazardous Decomposition Products; CO CO2 , Hydrocarbons
Hazardous Polymerization: Will not occur.

HEALTH HAZARDS DATA:
NOTE: Health studies have shown that exposure to chemicals pose potential risks which may vary from person to person. Exposure to liquids, vapors, mists or fumes should be minimized.

PRINCIPAL HEALTH HAZARDS:
Skin Contact: May cause irritation
Eye Contact: Strong irritant
Ingestion: May cause nausea, vomiting and diarrhea
Inhalation: May cause irritation

FIRST AID PROCEDURES:
Skin: Wash with soap and water.
Eyes: Flush with water. If irritation persists seek medical attention.
Ingestion: Do not induce vomiting. Seek medical attention.
Inhalation: Remove to fresh air.

PREVENTIVE MEASURES:
Skin: Always apply appropriate barrier cream to exposed skin. Wear impervious gloves (butyl rubber), coveralls and safety footwear.
Eyes: Chemical proof goggles or full face respirator if vapours cause eye irritation.
Ingestion: Wash thoroughly before consuming food stuffs.
Inhalation: Use only in well ventilated areas or use NIOSH approved respiratory protection with organic vapour cartridges.

CONTROL MEASURES & PRECAUTIONS
Keep container tightly closed. Do not consume food, drink or tobacco in work area or material storage areas. Use caution and personal cleanliness to avoid skin and eye contact. Avoid breathing vapours of heated materials. Use paper covering absorbent wipes and suitable disposable containers in work area.

SPILL, LEAK & DISPOSAL METHODS
Review fire and explosion hazards and safety precautions before proceeding with cleanup. Restrict access to area. Contain spill to prevent liquid from entering sewers or waterways. Recover free liquid and use an absorbent material (i.e. sand, vermiculite) to soak up balance. Place in suitable container for disposal.

DISPOSAL METHOD
Dispose only in a facility permitted to dispose of hazardous waste by Federal, Provincial and Municipal regulations.

SHIPPING INFORMATION

Shipping Name:
Hazard Class: Non Regulated
UN/PIN #:
Flashpoint:
WHMIS Classification: D2B


The information contained herein is based on data that we believe to be accurate. No warranty either expressed or implied is made. This information is offered solely for your consideration, interpretation and information.

Preparation Date: September 1, 2000
Prepared by: Ron Sherring, Industrial Plastics (1975) Ltd
Telephone #: (250) 727.3545